Stretch almost any fabric on a frame and a tufting needle will go through it. That isn't the test. The test is what happens on the thousandth stitch, an hour into a dense fill, with the cloth still expected to hold its shape.

So the short answer is no. Not every fabric works. The one that does is primary tufting cloth, a polyester or polyester-cotton weave made for this exact job. Everything else is borrowed from another craft, and most of it fails in a way you only find out halfway through a piece.

It's worth knowing why, though, rather than memorising a list of approved names. You need to know the three jobs the cloth is doing while you tuft. Once you know them, you can check any fabric yourself, and see for yourself why the alternatives below fall short.

What the cloth has to do

The cloth you tuft into is called the primary backing. Whatever it's made of, it has three jobs:

  • Let the needle through cleanly. The weave has to open around the needle and close again behind it, without tearing, splitting or leaving a hole that keeps getting wider.
  • Hold every stitch where it lands. Tufting doesn't tie knots. Until the glue goes on, the only thing keeping yarn in place is the grip of the weave.
  • Stretch drum-tight, then stay there. A slack patch halfway through a piece means uneven pile and a design that drifts out of shape.

A fabric that fails any one of these fails the whole piece, and usually not right away. That's why the wrong cloth is so expensive: you find out after the yarn and the hours have gone into it.

The first two are the checks we run before we stock any cloth. Every cloth we sell is run on a Craftphilia machine first. If the needle doesn't pass through smoothly and every stitch doesn't hold, we don't sell it.

You can run the same check on any unfamiliar fabric in about ten minutes:

  1. Stretch a scrap on the frame.
  2. Tuft a short straight line and a gentle curve.
  3. Turn the cloth over and look at the back.

Curves find weak cloth faster than straight lines do.

Monk's cloth: it depends which one

This is the name you'll come across most, and it's the least reliable name to buy by. Two different fabrics are sold as monk's cloth.

  • The one meant for rug work is an open 100% cotton basketweave with around 14 holes to the inch, usually with grid lines woven in.
  • Swedish weaving cloth is sold under the same name and was made for a different craft entirely. Check that the listing says punch needle or rug making before you buy.

Even the right one was built for a gentler tool. Monk's cloth comes from punch needle, where yarn is pushed through by hand, a stitch at a time. Cotton has very little spring. When a powered needle opens a hole wider, the hole tends to stay that way, and the weave keeps relaxing as the piece goes on. That puts it under the most strain on the third test: staying tight.

If you're punching by hand, it's the right cloth. If a gun or machine is doing the tufting, test it before you trust it with a full design.

Burlap, linen and canvas

These are the fabrics people reach for because they're cheap, or because they're already in the cupboard.

  • Burlap (jute or hessian) is the cheapest woven option and the roughest. Jute fibres are brittle, so they snap under the needle instead of moving aside. Burlap also sheds fine dust while you work, and its uneven weave makes straight lines hard to keep straight. It has a long history in hand rug hooking. Under powered tufting, it fails the first test early.
  • Linen is strong, but its weave is tight and it gives more than it should under tension. It also tends to cost more than cloth made for the job.
  • Canvas and denim feel sturdy, and that's the problem. The weave is too dense for the needle to open, so the needle gets forced through instead. These fail the first test before the other two even come into it.

Felt, fleece, knits and thin cotton

  • Felt isn't woven at all. With no weave to close around the yarn, stitches have nothing to hold them. Felt does have a place in tufting, just not this one: it goes on the back at the very end.
  • Fleece and knits stretch in every direction, and knits can unravel from a single hole. They fail the third test the moment you try to stretch them.
  • Muslin and thin cotton tear under tension, especially where you go back over the same area.

Primary tufting cloth: made for all three

Primary tufting cloth is the one fabric designed around these three jobs rather than borrowed from another craft. It has an open weave the needle can pass through without cutting threads. It's strong enough to stretch hard on the frame. And it usually has guide lines woven in. Those lines do more than help you place a design: if they bow or wave once the cloth is on the frame, the tension is uneven, and that shows up in the finished piece.

It comes in two main builds, a polyester-cotton blend and 100% polyester. We stock one of each, because they suit different work:

  • Craftphilia Tufting Cloth is 65% polyester and 35% cotton, white, with yellow guide lines. It's the standard choice for most pieces. If you're tufting with a gun, the lines double as a grid for measuring and placing your design.
  • Craftphilia Premium Tufting Cloth is 100% polyester, grey, with a tighter, steadier weave. It's for dense fills, fine detail, long runs and large formats, where the cloth has to stay tight for hours without slowly stretching out.

Neither one is better across the board. The question is which of the three tests your piece leans on hardest. A small piece with an open design sits comfortably on the standard cloth. A large piece packed with detail, running for hours, is what the Premium cloth is for.

Both come pre-cut for the CF05 and CF07, with or without the Expansion Kit. Each piece is deliberately larger than the tufting area: around 75 × 75 cm for the CF05's 50 × 50 cm, for example. The extra cloth gives the frame something to grip, and it's the border you'll glue and fold under when you finish the rug.

If you're buying off the roll for a gun frame instead, the cloth comes at a fixed width. That's worth planning around before you cut, and our breakdown of tufting costs covers how to keep the off-cuts down.

Here's every fabric in this guide, side by side:

Fabric Under a powered needle Best use
Primary cloth, polyester-cotton Opens cleanly, grips each stitch, stretches drum-tight and stays there Most tufted pieces, with a gun or a machine
Primary cloth, 100% polyester The same, with a steadier weave that holds tension longer Dense fills, fine detail, long runs, large formats
Monk's cloth Loosens and opens up as the piece goes on Punch needle
Burlap / jute Fibres snap; sheds dust; uneven weave Hand rug hooking
Linen Tight weave; stretches under tension Hand rug hooking
Canvas / denim Too dense for the needle to open The outside of a finished bag or cushion
Felt No weave to hold a stitch Backing, after gluing
Fleece / knits Won't hold tension; can unravel —
Muslin / thin cotton Tears under tension —

On a machine

A Craftphilia machine runs on standard primary tufting cloth. Nothing proprietary is required: any standard tufting cloth will work, ours or anyone else's.

What changes is which test matters most. With a gun, a good share of torn cloth comes from the hand rather than the fabric:

  • the gun tilted off square
  • the gun pushed in a direction it isn't pointing
  • the same spot gone over twice on a slow curve

A machine holds angle, pace and path the same way on every row, so that list mostly drops away.

That leaves the cloth itself. The frame is built to keep the tension once the cloth is properly installed, so you generally won't stop to re-tighten it mid-piece. Even so, the cloth has to hold its own shape for the whole run, and on a CF05 or CF07 a run is one to five hours. That's the case for the Premium cloth on bigger, denser work.

Every machine ships with tufting cloth for your first piece, so you won't have to make this choice until the second one.

Frequently asked questions

Can I tuft straight onto a tote bag, jacket or cushion cover?

No. A finished item can't be stretched drum-tight, and the needle doesn't pass through it cleanly. Tuft the design onto primary cloth instead, then glue it, back it and sew it into the item. Our guide to tufted wall art, shaped pieces and 3D objects walks through how panels become bags and cushions.

Is primary tufting cloth the same as backing cloth?

No. Primary cloth is what you tuft into. Backing cloth goes on afterwards, once the glue has dried. It covers the glue layer, gives the reverse a clean face, and on a floor rug gives it a non-slip underside. Our Craftphilia Backing Cloth is non-slip polyester that you trace and cut to your outline. Wall pieces can skip the non-slip layer entirely.

Can I use another brand's tufting cloth on a Craftphilia machine?

Yes. The machine works with standard primary tufting cloth, whoever made it.

How much bigger than my design should the cloth be?

Big enough for the frame to grip, plus a border of bare cloth around the design for glue and a hem. The pre-cut sizes already include this. If you're cutting your own, our rug finishing guide covers how wide that border needs to be.

Does the yarn change which cloth I should use?

Not much. As long as your yarn fits the needle, any primary cloth will take it. The yarn decision is about the needle and the finished pile, and our guide to choosing yarn for tufting covers it.

Leave a comment

Please note, comments need to be approved before they are published.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.

Latest Stories

Craftphilia Kickstarter update: 651 backers and US$529,306 pledged

Craftphilia Kickstarter Update: 651 Backers, $529,306, and What's Next

The campaign closed on 16 July at 5,262% of goal — 651 backers, US$529,306. What backers asked us, the five upgrades that came out of it, why shipping moved to September, and what happens next.

Read moreabout Craftphilia Kickstarter Update: 651 Backers, $529,306, and What's Next